Jump to content

  • Chat
  •  
  •  

Welcome to Formiculture.com!

This is a website for anyone interested in Myrmecology and all aspects of finding, keeping, and studying ants. The site and forum are free to use. Register now to gain access to all of our features. Once registered and logged in, you will be able to create topics, post replies to existing threads, give reputation points to your fellow members, get your own private messenger, post status updates, manage your profile and so much more. If you already have an account, login here - otherwise create an account for free today!

Photo

Fluon leaves litle pieces when applied? help please


  • Please log in to reply
2 replies to this topic

#1 Offline CatLord - Posted May 26 2018 - 5:37 AM

CatLord

    Advanced Member

  • Members
  • PipPipPip
  • 69 posts
  • LocationGreece-Chalkida

So when i use fluon i apply it 2 times and when i do it a second time it leaves these litle chunks of fluon behind and its not really that smooth and its very thick iam i doing anything wrong is it normal for it do that (it is applied on a plastic container not glass) 



#2 Offline drtrmiller - Posted May 26 2018 - 6:13 AM

drtrmiller

    Vendor

  • Members
  • PipPipPip
  • 2,714 posts

When Fluon is applied, the water evaporates, leaving behind an incredibly thin, dry film layer of PTFE particles.  PTFE is a very slippery plastic.  If you then brush another layer on top of this thin film, it will disturb the dried layer underneath, rubbing it off and rendering the application useless for containing insects.

First, you must use a damp paper towel to remove all the Fluon which was improperly applied.  The clumps of Fluon allow insects a foothold on which they may climb, and drastically reduce its effectiveness.  Allow the surface to dry completely, and verify it is clean and that no Fluon particles remain.  It may be necessary to clean the surface several times if all the Fluon is not removed the first time.

 

Then, apply only a single coating with as few strokes as possible.  Try not to go over the same area more than once.  If you must apply over the same area more than once, ensure that the area is still wet and that the dry film layer has not yet formed, which, in some cases may take only a few seconds, or else you will once again see the pieces of Fluon film which have clumped together and flaked off the surface.

 

If you read elsewhere that two or more coatings should be applied, ignore this.  The writer does not understand how Fluon works, and should not be offering instructions on how to use it.


Edited by drtrmiller, May 26 2018 - 3:44 PM.

  • CoolColJ and DrygonKing like this


byFormica® is the manufacturer of the iconic nectar feeders and Sunburst Ant Nectar.
byFormica ant products always deliver consistent performance, convenience,
and reliability, making them among the most beloved ant foods and kit enjoyed by
ant keeping enthusiasts worldwide. For more information, visit www.byFormica.com.

#3 Offline CatLord - Posted May 26 2018 - 10:39 AM

CatLord

    Advanced Member

  • Members
  • PipPipPip
  • 69 posts
  • LocationGreece-Chalkida

When Fluon is applied, the water evaporates, leaving behind an incredibly thin, dry film layer of PTFE particles.  PTFE is a very slippery plastic.  If you then brush another layer on top of this thin film, it will disturb the layer underneath, rubbing it off and rendering the application useless for containing insects.

First, you must use a damp paper towel to remove all the Fluon which was improperly applied.  The clumps of Fluon allow insects a foothold on which they may climb, and drastically reduce its effectiveness.  Allow the surface to dry completely, and verify it is clean and that no Fluon particles remain.  It may be necessary to clean the surface several times if all the Fluon is not removed the first time.

 

Then, apply only a single coating with as few strokes as possible.  Try not to go over the same area more than once.  If you must apply over the same area more than once, ensure that the area is still wet and that the dry film layer has not yet formed, or else you will once again see the pieces of Fluon film which have clumped together and flaked off the surface.

 

If you read elsewhere that two or more coatings should be applied, ignore this.  The writer does not understand how Fluon works, and should not be offering instructions on how to use it.

Wow thank you very very much!






0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users